Verilink SNMP Management (No Part Number) Product Manual Uživatelský manuál stáhnout pdf

Verilink SNMP SNMP-1

SNMP

SNMP Management

This part of the Management Section briefly describes the SNMP

(Simple Network Management Protocol) support provided by the

Verilink SCM and NCM controller modules. It contains an

explanation of the SNMP support that permits access to SCM- and

NCM-controlled nodes by the SNMP manager of your choice. You

should be familiar with SNMP and the SNMP manager you are using.

The SCC module supports SNMP for legacy products only. The

Quad/IMUX module supports SNMP as a standalone module. See

these application modules for further information.

Overview

SNMP is a network management protocol that is widely accepted for

controlling network equipment. SNMP has been implemented on

Verilink equipment to provide customers the flexibility to use the

Craft interface or an SNMP network management system. The SNMP

implementation provided by Verilink has been tested using HP

OpenView

and Verilink’s SNMP management system embedded in

the Verilink Node Manager.

The SCM and NCM supports the following MIB tables:

•

DS1 MIB Interface

•

Verilink Enterprise MIB

Getting Started

This document is a reference, not a tutorial. The preliminary steps

to using SNMP with your network SNMP management system are:

1. Compile the MIBs if they have not already been prepared.

2. Perform a request for [system] MIB to confirm the connection

to the node.

3. Access the [ncm.generic] table using the path:

iso.org.dod.internet.private.enterprises.verilink.as2000.ncm_generic

Go to the table

NCM

ODE

URR

ABLE

and select “Active“ via the

NCM Active Node Status to activate node control.

5. Go to [ncm_generic] table

NCM

HELF

NFO

ABLE

and set the

ncmShelfHardware to indicate the shelf type.

1 2 3 4 5 6 ... 13 14

Shrnutí obsahu

Strany 1 - SNMP Management

Verilink SNMP SNMP-1 SNMPSNMP ManagementThis part of the Management Section briefly describes the SNMP (Simple Network Management Protocol) support pr

Strany 2 - SNMP Interface Specifications

SNMP ManagementSNMP-10 Verilink SNMPTable 10 Far End Group3DS1 Fractional Group parameters are not supported in this release.dsx1FarEndIntervalUASs T

Strany 3 - Controlled

SNMP ManagementVerilink SNMP SNMP-11Verilink Enterprise MIBVerilink supports various enterprise-specific MIBs. Specific information on the Verilink

Strany 4 - MIB Tables

SNMP ManagementSNMP-12 Verilink SNMP•Status {manditory, not manditory}•Syntax {specifies values allowed by the object}•Description {provides explanati

Strany 5 - DS1 MIB Interface

SNMP ManagementVerilink SNMP SNMP-13DIU1. The “run BER test” option works only for the DIU 2130 module and not for the DIU/DBU or DIU/DDS modules.2.

Strany 6

SNMP ManagementSNMP-14 Verilink SNMP

Strany 7

SNMP ManagementSNMP-2 Verilink SNMPYou are now ready to manage the system. To change the active node being managed by your management system, return t

Strany 8

SNMP ManagementVerilink SNMP SNMP-3For example, you would calculate each interface’s number for a module (plug) in Shelf 2, Slot 2, as follows:Table

Strany 9 - DS1 Far End Group

SNMP ManagementSNMP-4 Verilink SNMPIn Table 3 below, column 1 specifies the modules controlled and column 2 specifies the associated MIB tables that

Strany 10

SNMP ManagementVerilink SNMP SNMP-5DS1 MIB InterfaceTables 4 through 10 list the various MIB-II interface parameters. The accompanying comments expla

Strany 11 - Enterprise MIB

SNMP ManagementSNMP-6 Verilink SNMPNOTE: To determine the clock source for Verilink products, see the Verilink enterprise MIBs.Table 5 DS1 Near End G

Strany 12 - Warnings

SNMP ManagementVerilink SNMP SNMP-7dsx1CurrentLESs The number of ES-L in the current 15-minute interval.dsx1CurrentBESs The number of Bursty Errored

Strany 13 - Verilink SNMP SNMP-13

SNMP ManagementSNMP-8 Verilink SNMPTable 6 Near End Group 3Table 7 Near End Group 4Object-Type Parametersdsx1IntervalIndex A number calculated with

Strany 14 - SNMP-14 Verilink SNMP

SNMP ManagementVerilink SNMP SNMP-9DS1 Far End GroupThe DS1 Far End group only applies to the SCC controller module.Table 8 Far End Group1Table 9 F

Komentáře k této Příručce

Žádné komentáře

Verilink SNMP Management (No Part Number) Product Manual Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Počítačový hardware Verilink SNMP Management (No Part Number) Product Manual. Verilink SNMP Management (No Part Number) Product Manual User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Počítačový hardware Verilink SNMP Management (No Part Number) Product Manual